Language
cs
da
de
english
es
fr
hu
it
nl
no
pl
pt
ru
sv
Home
IMPORTANT SAFETY INSTRUCTIONS
DANGER
WARNING
SAVE THESE INSTRUCTIONS
General Information
Proper Use
Equipment and Scope of Delivery
Servicing of Double-insulated Products
Environmental Protection
Explanation of Symbols
My bernette
Machine
Front view
Overview - Needle area
Overview Presser Foot
Overview - Looper area
Overview Threading area
Overview - Side panel
Symbols
Default Value
Accessories
Included Accessories
Accessories behind the Threader Cover
Accessories Box
Set Up the Machine
Working Area
Connection and Switching On
Connecting the Machine and Foot Control
Use of the Power Cable (only USA/Canada)
Switching the Machine and Sewing Light On/Off
Foot Control
Press the Foot Control
Handwheel
Machine cover
Open/Close the Threader Cover
Removing/Attaching the Knife Cover Insert/Coverstitch Insert
Thread Stand
Attaching the Spool Holder
Preparing the Thread Guide
Attaching the Spool Stabilizer
Place the Spool Disc
Using the Spool Net
Presser Foot
Raising/Lowering the Presser Foot
Lifting the Front of the Foot
Raising/lowering the presser foot using the Knee Lifter (Free Hand System)
Removing the Presser Foot Sole
Needle
Needle Holder
Changing the Needle
Positioning the Needles Up/Down
Threading the Needle Manually
Sewing Assistance
Using the Thread Cutter
Needle Pad
Attaching/removing the Knee Lifter
Attaching/Removing the Cut-offs Bin
Attaching/Removing the Freearm Cover
Attach the slide-on table.
Attaching the Decorative Threads Guide
Material selection
Check before Starting to Sew
Fabric selection
Selecting the Thread
Needle Thread
Check the Needle/Thread Combination
Looper Thread
Needle Selection
Detect Defective Needles
Needle Overview
Fixing Fabric Layers
Stitch selection
Stitch Type
Overlock stitches
Stitch Chart
Sewing Settings
Knife
Knife «On/Off»
Adjusting the Stitch Width
Setting the Cutting Width
Upper Looper Converter Hooked in/Hooked out
Setting the Stitch Length
Rolled Hem Selection Lever «N/R»
Setting Overlocking «N»
Setting Rolled Hem «R»
Setting the mtc micro thread control
Setting the Presser Foot Pressure
Thread Tension
Adjusting the Differential Feed
Default Value "1"
Gathering/Gather to fit "1.5 – 2"
Stretching "0.6"
Threading
Preparing for Threading
Needle Threads
Threading the Right Needle Thread RN/green
Threading the Left Needle Thread LN/yellow
Looper thread
Threading the Looper Thread
Threading the Looper Thread with an auxiliary thread
Using the Threading Wire
Changing the Thread
Knotting the thread
Changing the Needle Thread
Changing the Looper Thread
Stitch Optimization
Perfoming a Sewing Test for an Overlock Stitch
Optimizing Stitches
4-Thread Overlock with Integrated Safety Seam
3-Thread Super Stretch
3-Thread Overlock Wide (LN)
3-Thread Overlock Narrow (RN)
3-Thread Flatlock Wide (LN)
3-Thread Flatlock Narrow (RN)
3-Thread Narrow Seam
3-Thread Rolled Hem
2-Thread Wrapped Overlock Wide (LN)
2-Thread Wrapped Overlock Narrow (RN)
2-Thread Flatlock Wide (LN)
2-Thread Flatlock Narrow (RN)
2-Thread Rolled Hem
2-Thread Overlock Wide (LN)
2-Thread Overlock Narrow (RN)
3-Thread Picotstitch
Practical Sewing
Securing Overlock Stitches
Sewing in the Overlock Chain at the Start of the Seam
Sewing in the Overlock Chain at the End of the Seam
Securing Overlock Stitches
Knotting the Overlock chain
Removing a Stitch
Flatlock
Gathering a Seam
Increasing the differential feed
Pulling the Needle Thread
Sew Outer Corners
Sewing Inner Corners
Sew Outer Curves and Circles
Sewing Inner Curves
Appendix
Storage, Transport and Disposal
Storing the Machine
Transporting the Machine
Disposing the Machine
Machine
Cleaning the Machine
Cleaning the Looper Area
Clean Air Threader Pipes
Cleaning the Suction Feet
Oiling the looper area
Troubleshooting
Specifications